Lang Lang

Lead has long been recognized as a hazardous metal to fish and other wildlife (1). For humans, lead is a neurotoxic metallic element that can be absorbed by the body primarily through the lungs and stomach. Lead poisoning occurs when repeated exposure to a lead-containing environment happens so that lead is slowly accumulated in bones and tissues.  

Exposure to high concentrations of lead can cause serious health problems, including nervous system dysfunction of fetuses and infants, hemotoxic effects, reproductive dysfunction, gastrointestinal tract alterations, nephropathies, and Alzheimer's disease. Lead poisoning is related to anemia, because the activity of heme synthetic enzymes can be inhibited by lead ions (2). Lead is also a risk factor for hypertension in women (3). If lead poisoning is left untreated, it may damage kidneys, the nervous system, and the brain. Because of the possibility of permanent impairment, lead poisoning is particularly dangerous during infant development and for children under 7 years of age, who can absorb 50% of lead ingested, compared with adults who only absorb 10% of it (4). In 1985, the 

 defined childhood lead poisoning as blood lead levels >25 μg/L or 25 ppb. This definition has been revised down to 10 ppb based on new scientific evidence and observations that show children with lead levels as low as 10 ppb have decreased intelligence and slower neurological development (5). 

As a metal that has been widely used in industry for many years, lead is omnipresent in the environment—either from natural resources or from pollutants. In the United States, the average lead background level in soil is 7– 40 ppm (5–7). The maximum allowable lead level in food is 2 ppm (6). In agricultural products, food, raw dietary supplements, and pharmaceutical materials, lead usually exists at levels <1 ppm. To determine lead at ppm or sub-ppm levels, some analytical instruments with high-sensitivity detection capabilities are available, including inductively coupled plasma mass spectroscopy (ICP-MS) and graphite furnace atomic absorption spectroscopy (GFAAS) (8–13). Ion chromatography also has been used for lead determination; however, its sensitivity is not as good as that of ICP-MS and GFAAS (14–15).  

Although their sensitivities make ICP-MS and GFAAS the methods of choice for lead analysis, they are very expensive. For example, a typical ICP-MS instrument ranges in price from $250,000 to $750,000, and daily operational cost can be more than $1000. In addition, because only a small amount of sample solution can be introduced into the instrument, both ICP-MS and GFAAS require a very clean working environment, which adds maintenance cost to operate the instruments, especially an ICP-MS. Therefore, many analytical laboratories cannot afford an ICP-MS. Moreover, for laboratories in which lead analysis is not a routine task, it is not economically worthwhile to own a GFAAS instrument, even though it is less expensive (more than $20,000). Those laboratories prefer sending their samples to other laboratories for lead determination, even though sending samples to an outside laboratory costs money and time. 

To analyze low-level lead quickly, simply, and less expensively, a few analytical methods for lead determination have been developed in the past 10 years. Di Nezio et al. have reported a preconcentration technique involving flow injection spectrophotometry to detect lead in natural water samples (16). Other examples include a dibromo-p-methylsulfonazo spectrophotometric method to detect lead in biological samples, a resonance Rayleigh scattering method to detect lead in tap-water samples, and a fluorescent method to detect lead in soft drinks (17–19). However, these methods have their shortcomings: either they could only be used for water or liquid samples, or their detection limits were too high, or they were not tolerant of other common metal ions.  

The method reported in this article is based on the complex formation of lead with dithizone or diphenylthiocarbazone. Although dithizone has been used for lead analysis for more than half a century, limited research has been conducted on the sample digestion and few studies have been conducted on reagent recycling (20–23).  

Application of this complex reagent is very limited. A colorimetric method based on a lead-dithizone complex is the procedure recommended for lead analysis according to the US Pharmacopeia (24). Unfortunately, this method can be used only for simple samples and has serious shortcomings. For instance, the method is invalid for samples containing lead at levels <5 ppm. The shortcomings of the USP method include:   

It is not suitable for salts of alkali earth elements because a heavy precipitation is formed during the sample digestion process 

For many samples the digestion process is extremely time-consuming—it can take several hours or even days 

Detection limit is too high for almost all common samples 

The method generates too much waste of dithizone chloroform solution, which is both environmentally and economically unacceptable. 

We discuss a practical UV–vis spectrophotometric method for measuring trace amounts of lead (e.g., <1 ppm). The method is applicable to all organic and inorganic samples and eliminates all the shortcomings mentioned for the USP method. It is simple, economical (<$2/sample), reliable, and versatile for any type of sample. The procedure has been validated by standard addition method and a ICP-MS method. Its sensitivity is at sub-ppm levels, similar as those of ICP-MS and GFAAS. Using this method, lead in pharmaceutical, agricultural, food, and raw dietary supplement samples have been determined.  

 The following materials were used: lead stock standard solution, 1000 ppm (analytical grade); chloroform (HPLC grade); dithizone (diphenylthiocarbazone, p.a. grade); diethyldithiocarbamic acid sodium salt (p.a. grade); hydroxylamine hydrochloride (p.a. grade); ammonium hydroxide (ACS reagent grade); nitric acid (ACS reagent grade); hydrogen peroxide 35% (p.a. grade); and sulfuric acid (p.a. grade), which were all purchased from Acros (Morris Plains, NJ). Citric acid (reagent grade) and potassium cyanide (reagent grade) were from 

 (St. Louis, MO). Deionized (DI) water was from a reverse osmosis system at Culligan (Missoula, MT). All other chemicals, including hydrochloric acid, ethanol, phenol red, thymol blue, and so forth, either reagent or better grades, were obtained from Fisher Scientific (Denver, CO). 1% HNO

, 1% HCl, and 3 N HCl were prepared by mixing appropriate amount of DI water and the concentrate HNO

 and HCl, respectively. All samples were either obtained from the Department of Quality Assurance of 

 Inc. (Missoula, MT) or purchased locally. The instrument was a Cary 50 Bio UV–vis spectrophotometer from Varian (Walnut Creek, CA). 

 First, we diluted the 1000 ppm of lead stock solution with 1% HNO

 to 1.0 ppm. Then a 0.003% dithizone extraction solution was made as follows: 30 mg dithizone were dissolved in 1000 mL of chloroform, and 5 mL of ethanol were added as a stabilizer. The solution was stored in a refrigerator. Each time before use, we washed a suitable volume of the dithizone solution with half of its volume of 1% HCl. After washing, the aqueous phase was discarded. We prepared a 0.001% standard dithizone solution by dissolving 10 mg of dithizone in 1000 mL of chloroform and storing it in a refrigerator.  

To prepare the 30% ammonium citrate solution, we dissolved 60 g of citric acid in approximately 100 mL of DI water. Two drops of 0.1% phenol red in ethanol were added, and the pH was adjusted with ammonium hydroxide until the indicator turned from yellow to pink. Any lead present in the citric acid was removed by extracting the solution with 10 mL of 0.003% dithizone extraction solution. The extraction was repeated until the dithizone solution did not change color. The citrate solution was then diulted to 200 mL.  

To prepare the 2% ammonium cyanide solution, we dissolved 2 g of potassium cyanide in 15 mL of ammonium hydroxide, then diluted it with DI water to 100 mL. For the 5% potassium cyanide solution, we dissolved 25 g of potassium cyanide in sufficient water to make 100 mL. We removed lead from this solution by repeated extracting with 10 mL of 0.003% dithizone extraction solution until the dithizone solution did not change color. We removed any remaining dithizone from the aqueous solution by extracting with 10 mL of chloroform and repeated this process three times. We then diluted the cyanide solution with DI water to 500 mL. 

To prepare the 20% hydroxylamine hydrochloride solution, we dissolved 20 g of hydroxylamine hydrochloride in sufficient DI water to make ~60 mL. Five drops of 0.1% thymol blue in the ethanol solution were added, and the pH was adjusted with ammonium hydroxide until a yellow color appeared. We added and dissolved 0.4 g sodium diethyldithiocarbamate, and allowed it to stand for 5 min. The solution was extracted five times with successive 10 mL of chloroform. Drop by drop, we added 3 N hydrochloric acid until the solution became pink, and then diluted it to 100 mL with DI water.  

All reagent solutions were kept in a refrigerator and were stable for at least four weeks. 

Figure 1: The complex of lead and dithizone formed in weak basic solution. Lead to ligand ratio is 1:2. 

 In a weak alkaline solution, dithizone can form a stable complex with lead in a 2:1 ratio (see Figure 1). This complex has a maximum absorbance at 520 nm (see Figure 2). To obtain reliable results, the key step was to quantitatively dissolve and then isolate lead from the sample matrix. The optimized and validated analytical procedure follows. 

 Into a 250-mL beaker, weigh an appropriate amount of samples containing ≤25 μg of lead, such as 1–2 g of inorganic sample, 5 g of a mixture sample of inorganic and organic, or 10 g of organic sample. Add 10 mL of 1:1 H

O, v/v) and a few glass beads into the beaker. Cover the beaker with a piece of watching glass and heat the beaker on a hot plate until the sample becomes brown or dark brown.

Figure 2: Spectrophotometric scans of a blank dithizone solution (blue), 1 Î¼g/5 mL (red) and 4 Î¼g/5 mL (purple) of lead-dithizone solutions.

 (35%), until the organic materials are completely destroyed, which is indicated by the solution becoming clear. For mineral-containing samples, some white residue will remain. 

 For some samples of mixed organic and inorganic materials, H

 may not be able to destroy the organic components completely. In this case, alternatively adding H

 could speed the digestion. Wait for evolution of SO

 For alkaline earth-salt samples such as dicalcium phosphate, H

 should be avoided for digestion because it can form heavy precipitation with the metal ions and make the lead separation impossible. For these types of samples, neat nitric acid is sufficient. 

 After sample digestion, let the solution cool to room temperature. Wash the beaker with approximately 10 mL of DI water. Heat the solution again until SO

 smoke is evolved. Repeat the washing and heating one more time to remove any residual H

 is not completely removed, it will fail the lead extraction separation. 

 Add 10 mL of DI water to the sample beaker and stir to dissolve any water-soluble salt. Add 5 mL of 30% ammonium citrate solution, 2 mL of 20% hydroxylamine hydrochloride solution, and mix well. (Note: For alkaline earth-salt samples, do not add the 10 mL of DI water, instead add 20 mL of 30% ammonium citrate and 2 mL of 20% hydroxylamine hydrochloride solution, and mix well.) 

 Add two drops of 0.1% phenol red in ethanol. Carefully adjust the pH with ammonium hydroxide until the solution changes colors from pink to yellow then back to pink again. Cool the solution to room temperature. Completely transfer the sample to a 125-mL separatory funnel for liquid–liquid extraction of the lead. 

 Into the separatory funnel containing the sample solution, add 2 mL of 5% potassium cyanide solution and 5 mL of 0.003% dithizone extraction solution. Shake the separatory funnel for ~30 s, carefully releasing pressure from time to time. Drain the bottom dithizone phase to a 60-mL separatory funnel containing 20 mL of 1% HCl, which is used for back extraction of lead.  

Repeat the extraction three more times. Collect all the dithizone phases in the 60-mL separatory funnel. The original aqueous sample solution should be collected in a specific container for waste treatment.  

 Shake the 60-mL separator funnel for 45 s to back-extract lead to the acidic aqueous phase. Drain the dithizone phase into a beaker containing 20 mL of DI water to recycle the dithizone solution.  

 In the 60-mL separatory funnel, add 4 mL of 2% ammonium cyanide and 5 mL of 0.001% standard dithizone solution. Shake the separatory funnel for 45 s. Drain the dithizone solution into a 10-mL of centrifuge tube for the spectrophotometric determination of lead.  

 To construct the standard calibration curve, extract lead standard solutions containing 0.0, 1.0, 5.0, 10.0, and 25 μg of lead in the same way as described in steps 6–10. Using chloroform as a reference, measure the absorbances of the solutions at 520 nm. Create a calibration curve from the measured results. The 

 Measure the absorbance of the samples at 520 nm. Calculate the lead concentration based on the standard calibration curve obtained at Step 11.  

For quality assurance, we performed triplicate analyses for all samples.  

 The method was validated using two means: standard addition or method recovery and comparison with an accepted ICP-MS method. 

 Two samples with nondetectable lead were specifically chosen for lead recovery testing. These samples were spiked with 0.5  –3.0 μg of lead, and triplicate analyses were performed in the same manner as for the regular samples. Table I lists the lead recovery test results. In these tests, 10 g of dried hotdog bun powder and 2 g of green tea extract were used. 

Table I: Lead recovery test results (n 5 3). 

 Analytical results obtained with the UV–vis method have been validated by comparison with those acquired with a well-established ICP-MS method from a second laboratory. Table II provides method validation results for three different samples. Comparing the lead results obtained from the ICP-MS and from our UV–vis method, we can conclude that the UV–vis method is reliable and accurate. 

Table II:  Comparison of analytical results of lead from UVâvis and ICP-MS methods (Î¼g/g). 

 Using the UV–vis method described above, lead in several samples and at various levels has been successfully determined. Each sample was analyzed in triplicate and the average was reported. Table III lists analysis results of lead in some agricultural, food, and raw dietary supplement materials.  

Table III: Lead analytical results of some common samples (n = 3). 

In all the samples listed in Table III, 2.0 μg of standard lead were always spiked for quality assurance. The accepted recovery result at our R&D department is set at 1.8–3.0 μg (90– 150% of the spiked lead). For all the samples, the percentage recoveries always fall in the range of 90–120%, and none are out of the accepted range.  

Based on the lead analytical and recovery test results, the procedure described previously is effective for all materials included in the study. For most of the samples, the digestion time is <1 h. For some complicated dietary supplements, which might either contain certain compounds with high molecular weights or a mixture of organic and minerals ingredients, the digestion time may take as long as 2 h. In comparison, to digest this type of sample could take as long as 8 h, or even a couple days, if using the USP method (24).  

The last two samples in Table III, hydrox 6% FD and olive extract, are samples that would be extremely difficult to digest if using the USP method. For such samples, repeated treatment with H

 would dramatically shorten the digestion time, usually by 2 h. For salt samples of alkaline earth metals, such as dicalcium phosphate, the USP digestion method does not work (24). Dicalcium phosphate contains ~29% calcium and 70% phosphate. If concentrated H

 is used for the digestion, then a heavy precipitation is formed at pH adjustment (step 7). Mere HNO

 can also dissolve the sample, but if not enough masking reagent is used, then the calcium phosphate also will precipitate out when ammonium hydroxide is added to adjust the pH. In both cases, the precipitation makes it impossible to separate the lead from the sample solution. After trying different approaches and various masking reagents, we found the best way to avoid this problem was to:  

Use smaller amount of samples (e.g., 2 g instead of 5–10 g) (step 1) 

Add 30 mL of ammonium citrate as masking reagent instead of 5 mL (step 6) 

Stir the sample solution while slowly adding ammonium hydroxide to adjust the pH (step 7). 

Articles

The authors developed a reliable spectrophotometric method for determining and measuring trace amounts of lead in various samples.